Morley POWER WAH / VOLUME (PWOV) User Manual download pdf

Please take a few minutes to familiarize yourself with the features of your new pedal. With

common sense handling, it will last for years. We hope you enjoy using it as much as we

enjoyed building it. Feel free to call on us if you have any questions, comments or suggestions.

WA R RANTY (ALL PEDALS)

All Morley® pedals are warranted for two years from date of purchase. To obtain warranty service,

contact the store where purchased, call Morley 24 hours a day at 800-284-5172 (ext 14) or email

us at [email protected]

CONNECTIONS (ALL PEDALS):

9V: Use only Morley's 9 VDC 300 milliamp regulated adapter. Center Polarity is negative.

IN: Input jack. Plug instrument into this jack using 1/4" guitar cable.

OUT: Connect amplifier to this jack using a 1/4" guitar cable.

Morley Pedals (except Model PLA) are NOT recommended for use in effects loops.

NOTE: You 'll find cords fit very tightly into the input/output jacks. The tight fit helps prevent the

cord from being accidentally unplugged. Make sure cords are completely plugged in for best results.

ELECTRO-OPTICAL CIRCUITRY (ALL PEDALS):

The light from the LED (Light Emitting Diode) that shines on the

LDR (Light Dependent Resistor) is controlled by a shutter placed

between the two devices. Our unique Electro-Optical design ensures

smooth pedal control without unwanted noise typical with

potentiometer (pot) controlled pedals.

AC ADAPTER (ALL PEDALS)

All Morley pedals use Morley's 9VDC 300 milliamp regulated adapter. Center pin polarity

is negative. Using a non-regulated adapter could cause a low frequency hum in your amplifier.

Using an adapter with the wrong polarity may damage the pedal.

BATTERY (ALL PEDALS)

All Morley pedals are designed to use one 9V battery when not using an adapter. We suggest you

use a good quality alkaline battery. To prolong battery life, unplug your cord completely from the

input jack when not using the pedal. When the pedal is not used for extended periods, remove the

battery from the pedal or replace it every six months to prevent leakage problems.

BATTERY REPLACEMENT (ALL PEDALS)

When battery becomes weak, the effect will become weak and signal may become slightly distorted.

Remove the battery door located on the bottom of the pedal (a short cord is attached to the door to help

prevent loss). Once the door is off, the old battery can be removed and a new battery plugged in. Make

sure the polarity (+/-) is correct before inserting the new battery. When you replace the battery door,

you will notice it fits tight against the battery. This prevents battery from rattling inside the pedal.

For Tripler, Quad Box and ABY you must remove bottom cover to install battery.

THANK YOU FOR CHOOSING A MORLEY® PEDAL.

YOU NOW OWN THE BEST PEDAL MADE!

POWER WAH FEATURES (MODEL PWO)

· WA H level Control: This knob controls the output level of the Wah effect.

· WAH On/Off Switch: This switch turns the Wah effect on/off.

· HQ

Inductor: Morley's Modern Inductor with Vintage Tone.

· LED WA H On/Off Indicator: When the LED is on, Wah is engaged.

· "TrueTone Bypass" Morley's buffer circuit prevents loading of the guitar

signal ensuring no volume or tone is lost in Wah and Bypass modes.

PWO SPECIFICATIONS

POWER: 9V Battery or 9VDC 300 mA regulated adapter (center negative)

CURRENT DRAW: 5 mA @ 9 VDC

INDICATOR: LED on: Wah mode, LED off: Bypass

DIMENSIONS: 9.13" (L) x 5.88" (W) x 2.75" (H)

WEIGHT: 3.3 lb./ 1.51 kg

PRO SERIES II DISTORTION WAH VOLUME FEATURES (MODEL PDW-II)

· LED indication: Located above the "WAH" and "Distortion" switches.

VOLUME / WA H Switch: Switches between Wah and Vo l ume modes.

DISTORTION On/Off Switch: Turns the distortion effect on/off.

· DRIVE control: Adjusts the amount of distortion.

TONE control: Colors distortion.

LEVEL control: Adjust the amount of output from the distortion.

· "TrueTone Bypass" Morley's buffer circuit prevents loading of the guitar

signal ensuring no volume or tone is lost in all pedal modes.

PDW-II SPECIFICATIONS

POWER: 9V Battery or 9VDC 300 mA regulated adapter (center negative)

CURRENT DRAW: 7 mA @ 9 VDC

INDICATOR: Wah mode LED on, Bypass mode LED off.

Distortion mode LED on, Bypass mode LED off.

DIMENSIONS: 9.13" (L) x 5.88" (W) x 2.75" (H)

WEIGHT: 3.3 lb./ 1.51 kg

POWER WAH VOLUME FEATURES (MODEL PWOV)

· WAH level Control: This knob controls the output level of the Wah effect.

· WAH On/Off Switch: This switch turns the Wah effect on/off. The pedal is

in volume mode when the Wah is turned off

· HQ

Inductor: Morley's Modern Inductor with Vintage Tone.

· LED WA H On/Off Indicator: When the LED is on, Wah is engaged.

· "TrueTone Bypass" Morley's buffer circuit prevents loading of the guitar

signal ensuring no volume or tone is lost in Wah or Vo l ume modes.

PWOV SPECIFICATIONS

POWER: 9V Battery or 9VDC 300mA regulated adapter (center negative)

CURRENT DRAW: 6 mA @ 9 VDC

INDICATOR: LED on: Wah mode, LED off: Volume mode

DIMENSIONS: 9.13" (L) x 5.88" (W) x 2.75" (H)

WEIGHT: 3.3 lb./ 1.51 kg

Summary of Contents

Page 1

Please take a few minutes to familiarize yourself with the features of your new pedal. With common sense handling, it will last for years. We hope you

Related models: POWER WAH (PWO)

Comments to this Manuals

No comments

Morley POWER WAH / VOLUME (PWOV) User Manual

Browse online or download User Manual for Musical Instruments Morley POWER WAH / VOLUME (PWOV). Morley POWER WAH / VOLUME (PWOV) User Manual

Summary of Contents

Related models: POWER WAH (PWO)

Comments to this Manuals

Related products and manuals for Musical Instruments Morley POWER WAH / VOLUME (PWOV)